# Stribog UAS unpacking

{% embed url="<https://youtu.be/YYTwng3XMEQ>" %}

*Note* that the video is divided into sections which shows what is currently being showcased in the video. Alternatively, English and Ukrainian subtitles are available. (Unpacking Stribog UAS.mp4)

Alongside the video, we also supply a quick list of actions to do when unpacking Stribog UAV from its packaging:

* Put the UAS out of the packaging
* Attach UAS legs
* Make sure legs are attached properly
* Check if there is a camera cover attached, if so, please remove it before flight
* Unfold arms
* Attach UAS antennas
* Make sure antennas are fastened properly
* Connect the batteries
  * Put the balance connector into the holder to keep it in its place during flight
  * Slide the battery plate into the rails on the top plate of the UAS
  * Pull the safety pin upwards to secure the battery position
  * Connect the battery power connector to the UAS power input
  * Repeat the process for second battery
* Remove interceptor detection module cover
* Attach interceptor detection module

***

### Unpacking <a href="#unpacking" id="unpacking"></a>

Unpack your system from the packaging. Each system consists of a total of 4 backpacks, where 3 backpacks carry one UAV each, and 1 operator backpack carries all accessories needed for operation. To effectively operate the system, the user needs at least 1 backpack with a UAV and the operator backpack.

**Unpacking UAV backpack**

{% tabs %}
{% tab title="Step 1" %}

<figure><img src="/files/PwD6OsXZHqGwb6kDOnvd" alt=""><figcaption><p>Opened packaging</p></figcaption></figure>

Open your package and **proceed to Step 2**.
{% endtab %}

{% tab title="Step 2" %}

<figure><img src="/files/xbRIy0XpG5UiXtfxD5xj" alt=""><figcaption></figcaption></figure>

{% hint style="danger" %}
Please note that the drawing slightly differs from the Nexus Stribog UAS to get full understanding of the packaging please refer to the [instructional videos](https://www.youtube.com/watch?v=YYTwng3XMEQ).
{% endhint %}

Unpack your Nexus Stribog UAS package. You can find here following items in the foam packaging:

1. ~~**Doodle Labs antennas**~~**&#x20;- Doodle Labs antennas for UAV are placed in the side pockets**
2. ~~**Doodle Labs wearable radio**~~**&#x20;- the doodle labs wearable is placed in accompanying backpack carrying all of the necessary accessories for operation**
3. ~~**Battery charger including cables**~~**&#x20;- the battery is placed in accompanying backpack carrying all of the necessary accessories for operation**
4. **Nexus Stribog UAS with already mounted propellers**
5. **Two battery packs**
6. **Six Stribog UAS legs**
7. **Two spare propellers**

In the pockets and inside of the backpack, in which your Nexus Stribog UAS came, you will also find:

1. **2mm hex screwdriver**
2. **2.5mm hex screwdriver**
3. **8mm combination wrench**
4. **Doodle Labs antennas**[**https://app.gitbook.com/o/FfahtpTdNBIeKGBfIMbG/s/wI5SnA40nkGzeqpCRvuH/\~/changes/150/uas-platforms/nexus-stribog-uas-1**](/uas-platforms/nexus-stribog-uas-1.md)
   {% endtab %}
   {% endtabs %}

#### Unpacking operator backpack

{% tabs %}
{% tab title="Step 1" %}

<figure><img src="/files/J86MpJldwa0yf9vniuAS" alt=""><figcaption><p>Operator backpack schematics</p></figcaption></figure>

Unpack the backpack. You can find the following items here:

* **(1) GCS - ruggedized laptop**
* **(2) Ethernet cable (25m)**
* **(3) Power adapter suitable for charging the rugged laptop, DoodleLabs wearable, and controller**
* **(4) Mast**
* **(5) Controller in additional packaging**
* **(6) Battery charger**
* **(7) Spare batteries inside a rugged Peli case, also usable as a preheater for batteries**
* **(8) Set of screwdrivers**
* **(9) Antenna cable for directional antenna**
* **(10) Directional antenna**
* **(11) DoodleLabs wearable**
* **(12) Omnidirectional antenna**
* **(13) High-power USB-C charging cables**
  {% endtab %}
  {% endtabs %}

***


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://docs.airvolute.com/uas-platforms/nexus-stribog-uas/stribog-uas-user-manual/getting-started/unpacking-and-assembly.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.